Fog-Off Make your mirror fog free forever!

State of the art Fog off mirror heating pads maintain a constant temperature without the use of bulky thermostats

No jamming No noise and No fog!

Fog-Off is the quiet achiever that works at a flick of a switch without putting a hole in your budget!

"I write to advise you that I am extremely pleased with the performance of the Fog-Off mirror heating pads which I have had installed in my house."

Fog-Off is the registered name and trademark of a unique and patented product, which prevents bathroom mirrors steaming up.
              Home
              Order Heated Mirror Pads
              Contact Us
              Bathroom Mirror Pads
              Bathroom Mirrors Application
              Mirrors Project
              Press Releases
              Recommendations
              Links


Fog-Off consists of a self-adhesive 1 mm thick thermostatic plastic sheet that are designed to conduct electric energy when it is then connected to the power source (usually the bathroom light switch).
Each pad has a self adhesive backing paper, which when removed allows the pad to be adhered permanently to the backs of bathroom mirrors.


Actual Fog-Off heated mirror pad unit that sits behind your mirror designs



Fog-Off heating mirror pads are manufactured & available in three sizes:

 
  • 500 mm x 300 mm
  • 500 mm x 600 mm
  • 500 mm x 800 mm
Fog-Off poses no risk of electrocution of burning whatsoever, & meets every Australian building regulation & safety standard.


With the cable installed & connected to the light switch
(240v) power supply
the simple action of activating the light,
the “Fog-Off” unit is automatically activated.
In a few minutes this warms the mirror to the point
where steam can not condense.
Giving a very clean clear area (the size of the pad plus 20%)
while allowing a person to use that area in steamy conditions without having to wipe the mirror or use a hair dryer which is common practice.

There is none better in the world.

While Fog-Off is still relatively unknown amongst private home owners in Australia it is already a well established brand amongst the Australian hotel industry, having been installed in over hundreds of hotel bathrooms in just the past 10 years.
The benefit to hotels, however, is not just aesthetic. Because Fog-Off stops mirrors needing to be wiped, it also prevents wear and tear and damage to mirrors by guests’ wiping mirrors while wearing rings or other abrasive jewellery and it removes the need to touch the mirror, Fog-Off also reduces time needed for staff to clean after guests have vacated the room.

This innovative product will prevent the build up of condensation on your bathroom mirrors.
You will never have to use your hand, towel or elbow to remove fog from your bathroom mirrors again.


While there are other products designed to inhibit mirror steaming, they are more complicated, expensive and difficult to install.
The total Fog-Off package, including all wiring and connections, costs less than $200, irrespective of mirror size and can be installed by any competent electrician or glazier in minutes.

Most architects, project managers and builders are aware of the existence of either Fog-Off or competitive products, but usually rely on the client requesting they be installed as Fog-Off is seen as a personal selection to improve quality living.

Fitting Fog-Off
Fog-Off pads are supplied with a one-metre long 1 mm cord. Standard voltage is 240 volts, with power rating of 60 watts per square metre. The thickness is less than 1 mm. Fog-Off must be fitted by a licensed electrician AS3000 standard and protected by a 5 amp fuse or a circuit breaker.
The pad should be positioned immediately above the basin, with its lower side located at a minimum height of 1250 mm above floor level, being self adhesive, it attaches to the back of any framed or unframed mirror and should be mounted not less than 50 mm from the edge of the mirror. Mirror fixing devices should not touch or pass through the Fog-Off pad. Allow 200 mm minimum clearance for screw fixing		 Fog free misty free mirrors when you need it most!
  • Mark with pencil on rear of mirror where Fog-Off fog free element is to be applied.
  • Ensure back of mirror is clean.
  • Remove adhesive backing panel from Fog-Off fog free element.
  • Position one edge of the element to rear of mirror.
  • Apply even pressure by hand to ensure the element is fixed.
Normally the pad can be connected into the bathroom lighting electrical circuit. Alternatively, it can be connected into the fan circuit or through a separate switch. Fitting must conform to the requirements of your electricity supplier and of the relevant government authorities.
NB: do not use element that has been cut or punctured (contact your supplier). Avoid applying element where screws or mirror fixings will penetrate element.

Warranty

Fog-Off is guaranteed for ten years, provided it is fitted in accordance with the instructions supplied. The warranty provides only for free replacement or repair of the product if it is returned to Fog Off within ten years of the date of purchase.

Home
Order Heated Mirror Pads
Contact Us
Bathroom Mirror Pads
Bathroom Mirrors Application
Mirrors Project
Links		 Press Releases
Recommendations
Shipping & Returns
Privacy
Sitemap

© Copyright 2009 Fog-Off

Website by Scarborough Web Design Ltd